INVESTIGADORES
CADUS Luis Eduardo
artículos
Título:
SYNTHESIS AND CHARACTERISATION OF La1-xCaxFeO3 PEROVSKITES-TYPE OXIDE CATALYSTS FOR TOTAL OXIDATION OF VOLATILE ORGANIC COMPOUNDS
Autor/es:
BARBERO, BIBIANA P; LUIS EDUARDO CADUS
Revista:
APPLIED CATALYSIS B-ENVIRONMENTAL
Editorial:
Elsevier
Referencias:
Año: 2006 vol. 65 p. 21 - 30
ISSN:
0926-3373
Resumen:
Abstract La1xCaxFeO3 perovskite-type oxides with x = 0, 0.2 and 0.4 were prepared by the citrate method and characterised by means of X-ray diffraction (XRD), X-ray fluorescence (XRF), surface area measurement BET, X-ray photoelectron spectroscopy (XPS), Fourier transformed infrared spectroscopy (FT-IR), laser Raman spectroscopy (LRS), oxygen temperature-programmed desorption (O2-TPD) and temperatureprogrammed reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. diffraction (XRD), X-ray fluorescence (XRF), surface area measurement BET, X-ray photoelectron spectroscopy (XPS), Fourier transformed infrared spectroscopy (FT-IR), laser Raman spectroscopy (LRS), oxygen temperature-programmed desorption (O2-TPD) and temperatureprogrammed reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. 1xCaxFeO3 perovskite-type oxides with x = 0, 0.2 and 0.4 were prepared by the citrate method and characterised by means of X-ray diffraction (XRD), X-ray fluorescence (XRF), surface area measurement BET, X-ray photoelectron spectroscopy (XPS), Fourier transformed infrared spectroscopy (FT-IR), laser Raman spectroscopy (LRS), oxygen temperature-programmed desorption (O2-TPD) and temperatureprogrammed reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. 2-TPD) and temperatureprogrammed reduction (TPR). The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation and/or contamination. Moreover, controlling the calcination temperature, specific surface areas adequate for catalysts to be used in oxidation reactions are achieved. The structure refinement by using the Rietveld method indicates that the partial calcium substitution modifies the orthorhombic structure of the LaFeO3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. 3 perovskite towards a less distorted one. From XRF and XPS, a slight surface enrichment in lanthanum and calcium was detected. XRD, FT-IR and TPR results indicated that the electronic debalance caused by the partial substitution for La3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. 3+ by Ca2+ is compensated by an oxidation state increase of a part of Fe3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions. 3+ to Fe4+. O2-TPD results revealed that at a substitution level higher than x = 0.2, oxygen vacancies are also formed to preserve the electroneutrality. Finally, an improvement of the catalytic activity in propane and ethanol combustion was observed on the substituted perovskites. Correlating this with the characterisation results, the active sites would be associated to the Fe4+ ions.4+ ions.